This product is specially developed for remote control cars and boats. It supports multi-device and multi-user simultaneously with fast response speed and strong anti-interference ability, very low power consumption and high receiving sensitivity. Special speed limit function. Besides, TG-3 2.4Ghz remote system with intelligent design, can be widely used. Let beginners can control the car or boats within limited speed range. It also has a special throttle limit switch!
High receiving sensitivity.
3CH remote control for RC cars and boats.
Multi-device and multi-user simultaneously.
Built-in design of the antenna in the transmitter.
Very low power consumption, and stable performance.
Fast response speed and strong anti-interference ability.
TG3 2.4Ghz remote system with intelligent design can be widely used.
Specifications of Transmitter:
Model name: TG3
Remote control frequency: 2.4GHz
Mode type: RC car/boat
RF range: Less than 20dbm
Low voltage warning: yes (less than 4V)
Powere supply: 4 * 1.5V AA Battery (not includeded)
Transmitter size: 225 * 135 * 75mm (artificial measurements error allowed)
Transmitter weight: 285g
Specifications of Receiver:
Mode name: TG-3
Model type: RC Car / boat
Power: 4.0 – 6.5V DC
Receiver size: 30 * 18 * 13mm (artificial measurements error allowed)
Receiver weight: 4g
Suitable for 2.4G 3CH Transmitter
Package size: 26 * 17.5 * 9.5cm / 10.2 * 6.9 * 3.7in
Package weight: 455g / 1.00lb
Brand gift box package
1 * GoolRC TG3 Transmitter
1 * TG-3 Receiver
1 * Paster
1 * Match Line
1 * English Manual
Questions & Answers
are you able to adjust the steering L and steering R limits, throttle B, throttle F with this transmitter?
Yes. You can adjust sub trim left and right as well as throttle trim and fine tune sensitivity
By Lola on May 13, 2018
Will it work on a rc car of a 40.680 MHZ?
This is a 2.4ghz it comes with its own reciver so the old radio system and reciver is no longer needed
By 83cj7jeeper on May 8, 2018
When signal is lost, the receiver gets stuck to full throttle until signal is established…not good if losing control, my truck is 35lbs ..Fix?
Take the receiver and remove it from your vehicle. Next, turn the transmitter over and slide off the battery door. Remove the installed batteries and put them somewhere safe. Take the receiver and place it in the battery compartment and replace the door. Take your new assembly and throw it in the garbage where it belon… see more Take the receiver and remove it from your vehicle. Next, turn the transmitter over and slide off the battery door. Remove the installed batteries and put them somewhere safe. Take the receiver and place it in the battery compartment and replace the door. Take your new assembly and throw it in the garbage where it belongs and order a new TX/RX combo. These consistently lose signal, jitter, studder, and randomly peg out inputs. I swapped in an Axial combo to see if it was my ESC or Servo. It wasn’t. see less
By D. J. Quintero on May 3, 2018
can you put this on an electric skateboard?
If you are talking about a real skateboard, I would not recommend it. A small RC skateboard, sure with the right components.
By Larry on April 30, 2018
Can I use a 9v or rechargeable 9v to power the receiver ? I only need it to trigger an Eflite payload release
I would not recommend it.
By Larry on April 15, 2018
Good for an axial bomber?
I love mine. It’s inexpensive but works great. I really like the 3 way throttle setting (LMH) for when I’m crawling. I bought one and then some spare receivers since they are so easy to bind. It’s lightweight but doesn’t feel cheap. Good feel to the grip and wheel. Throttle and Steering trim. Steering rate. And agai… see more I love mine. It’s inexpensive but works great. I really like the 3 way throttle setting (LMH) for when I’m crawling. I bought one and then some spare receivers since they are so easy to bind. It’s lightweight but doesn’t feel cheap. Good feel to the grip and wheel. Throttle and Steering trim. Steering rate. And again, a LMH setting for the throttle. It’s nice on my D90 to slow it down so I don’t do wheelies when I’m crawling with it. I use this for my Orlandoo Jeep and my 1/10 D90. Channel 3 is only a push-button so 2 Settings (full left, full right on a servo), not good for a winch. see less
By Charles on March 22, 2018
Will the receiver fit in the Traxxas receiver box on a Stampede?
The reciever included with this radio is a micro rx so yes it will fit the rx box on the stampede as well as most other rx boxes.
By leonardo rosiles-cervantes on March 11, 2018
How do you set end points on this receiver for the 3rd channel
Near as i can tell 3rd channel works for winch. I could be wrong, sorry if i am
By glenn ahrensfeld on March 1, 2018
Does this come with bind plug
Yes, and it is already bound to the receiver it comes with.
By Larry on February 21, 2018